Our products

Y5 series prop which has 10% more pitch than X4 series. This drive dog prop has a 1/8" bore and can be threaded 4mm if required.

This prop has a 1/8" bore and can be threaded 4mm.  10% more pitch than the X435. Use when your running out of top end speed with your X435.

 37mm diam. with 10% more pitch that an X437/3 prop"

The same blade profile as the X4 series props but has 10% more pitch than the X447. Good for high powered 7.5cc motors.

X447 pitch is 2.59"
Y547 pitch is 2.85"

Ideal replacement for your X457, when your engine can't quite drive an X460. Great on a 15cc mono and cats."

72mm dia. x 110.9mm pitch.  For use on the higher torque twin inline 26cc + motors using surface drive on Monos,  Hydros & cats. A good prop for 30-35cc motors."

Pulley wheel to replace the cord pullstart on Zenoah and similar engines for use with starter belt 

One of Octuras original series props that has been made for fast electric hydros/riggers.

This was one of the original moderate lift OCTURA drive dog props from the 1950's, a series that was never advanced on and for which there are only 4 sizes. Produced only in the blue plastic this material is very strong. Back in the 60' a customer used to run the Z60 on a multi hull with a Rossi 90. He never broke a blade off in normal racing and use, except when coming into contact with another hull, which of course is the case with ali props.
For 2011 OCTURA have now added a fourth prop in metal, suitable for fast electric hydros

The 4 sizes are Z50, Z55 & Z60 & Z35/3

 Standard Zenoah 260marine engine

 ZTW Seal 200amp ESC  G2

      Multiple protections: start-up, over-heat, low-voltage cutoff, signal loss, phase loss, over-current, abnormal power-on voltage, over-load protection.

4S to 8S with BEC
Forward only plus forward and reverse
200amp
Burst  1200amp
Max. voltage  37v

The ZTW Seal Series is high-end and high quality and good performance ESC, is designed specifically for RC Boat applications, we all know that that boaters crave for more power than cars and airplanes and we have come up with a whole new way to put the power to the water-cooling brushless speed controls for marine applications. This series of ESC also feature with good water cooling system, using state-of-art MOSFET, exposed finned sink.

• Water cooled
• Normal Continuous Current 300A
• Burst Current 1000A
• Battery 18-42 NiMh / 6-14 Lipo
• Power Wires 6 AWG, 160mm-Red/160mm-Black
• Motor Wires 6 AWG, 160mm-Orange/Yellow/Blue
• Signal Wires（Black/Red/White）300mm with Normal JR Male

One of the original design propellers from Octura. This propeller works extremly well as a convention drive prop but works very well on Hydros and can be used on monos depending on the drive set up. It has a medium to high lift.


1427becu..................£9.95
1440becu..................£12.25
1445becu..................£12.55
1450becu..................£14.00
1452becu..................£14.55
1455becu..................£15.10
1455/3becu...............£16.95
1457becu..................£16.10
1457RH.....................£ 1.35**
1460becu..................£14.40
1462becu..................£16.85
1462RH.....................£ 1.55**
1465becu..................£16.95
1467becu..................£17.95
1470becu..................£18.15
1475becu..................£19.25

** Glass filled plastic only
Many of the props are available in glass filled plastic which makes them fairly robust.
The brown coloured props in the picture are the 1400

Smallest of the 19 series rigger/hydro props with a 1/8 (.125") bore"

Balance polish ABC H series props

The M series props have been modified to help unload them by the removal of the ears.<BR><BR>  The smallest 3 blade prop for a 1/8" shaft.

 1/8" bore which we can thread 4mm if required. 27mm dia. 1.5" pitch

The smallest of the X6 series with a 1/8 bore. Can be threaded 4mm."

4mm S/steel drive dog

Octura .098" flexi cable, per 12" (305mm)

Bobbin type coupling for connecting engine to a solid shaft. using 20 x 15mm bobbin.

MMS 20.5" x 3/16" flexi shaft made with heavy duty gold anodised cable.

Made to order only. 10 to 14 days
A supurb model of a Class 1 & 2 Offshore power boat. Suitable for engines from 7.5cc nitro up to 26cc petrol. Best suited to an 11cc motor. One of the most stable and fast hulls on the market today.

Aeromarine small CNC machined rudder with integral water pick up. 4.75" (117mm) blade.

AEROMARINE Large 45/90Rudder with 6" blade and integral water pick up. Also suitable for small 21 size hulls